
Jowi Morales Social Links Navigation Contributing Writer Jowi Morales is a tech enthusiast with years of experience working in the industry. He’s been writing with several tech publications since 2021, where he’s been interested in tech hardware and consumer electronics.
maxumus-max Seems a bit redundant since you're supposed to keep pairs as twisted as possible Reply
bit_user maxumus-max said: Seems a bit redundant since you're supposed to keep pairs as twisted as possible You have to untwist them to attach a connector. Like the picture shows, I think he was just untwisting the very end. Upon reading the headline, I was also concerned about the extent of untwisting. But, I think the main length of the cable is still twisted, which is done to make the pairs resilient to induced noise. Untwisting the entire length of a Cat 6 cable would defeat this signal integrity mechanism and potentially make it incapable of hitting the rated speeds. Reply
bill001g The title is misleading. What he is doing is installing infrastructure cables not making 50000 patch cables. The time it takes to untwist a few wires is nothing compared to hauling a ladder around and doing the setup. Maybe he does 100 cables into a patch panel not 50,000 at one time The guys I used to watch install patch panels did it all by hand and were extremely fast. The machine he is trying to copy is what they use when they make patch cables in a factory sitting at a table. Reply
AmirTHforum Why doesn't anyone comment or complain about the obvious problem here? And that is the archaic way we connect Ethernet. I don’t care when Ethernet or the physical connection was invented, but that must be the worst design ever. And why hasn’t it been updated? Am I wrong about this? Reply
bit_user AmirTHforum said: And that is the archaic way we connect Ethernet. I don’t care when Ethernet or the physical connection was invented, but that must be the worst design ever. And why hasn’t it been updated? I guess you're talking about the RJ-45 connector? If so, I'd agree that it's not optimal. I can't count how many times I've seen Ethernet connectors with a broken latch. I've even had a batch where latch seemingly broke through simple plastic aging, because a bunch of my cables had latches with zero springiness and I'm really careful with my cables so I know that wasn't due to them getting snagged on something or being abused. What I found disturbing about that is how at least one of these cables seemingly required the pressure exerted by the latch for the metal fingers to make good contact. Because, even though the cable was fully inserted, I found that the connection was unstable. I think two factors keep RJ-45 in use: backwards compatibility and the relative ease of attaching connectors after running bare cable through a conduit. I'm not an expert on connectors, but it seems to me that anything aiming to displace RJ-45 would need to be similarly cheap & easy for installers to crimp on. I don't know if there's anything which meets those objectives that's significantly better than RJ-45. As for the rest of the cable, shielded twisted-pair seems to be pretty much the gold standard in copper cable technologies, which is what the highest-grade Ethernet cables use. Reply
bill001g bit_user said: I guess you're talking about the RJ-45 connector? If so, I'd agree that it's not optimal. I can't count how many times I've seen Ethernet connectors with a broken latch. I've even had a batch where latch seemingly broke through simple plastic aging, because a bunch of my cables had latches with zero springiness and I'm really careful with my cables so I know that wasn't due to them getting snagged on something or being abused. Where I worked they had a seeming simple project of swapping out a rack of switches with newer models. This had been sitting untouched and working fine for 5yrs. About 200 cables to unplug and plug back in was the theory. The plastic ends on those cables were so brittle that we had plastic tabs all over the floor. That room ran kinda warm so likely helped damage the plastic. So now a 1 hr project took all day because all new patch cable had to be found and run. Goes back to if it isn't broke don't fix it rule i guess. Reply
bit_user Informative post! I do have some notes, however. : ) Misgar said: I've had my fair share of RJ45 cable problem and have stopped buying patch leads with exposed plastic latches (see @bit_user's comments above). The cables with the failed latches that no longer make good contact did have an integrated latch guard, in the cable boot. It was apparently just poor quality plastic that lost its spring tension as it aged + a physical plug which maybe didn't fill the socket all the way and depended on that spring tension for good contact. In other words: a cheap cable ]. Misgar said: If you want an alternative to RJ45, consider SFP/SFP+ (Small Form Pluggable). Yes, but. They're more bulky, the DAC cables have worse bending radius and length limitations, and those connectors are still uncommon on commodity consumer switches and especially networked devices. I prefer to use integrated Ethernet, when possible. I have a pair of 10G cards with SFP+ on them and two of my switches have some SFP+ ports. So, I'm not a stranger to the technology, but I feel it's not a substitute for many of the cases where RJ45 is used. The added cost of the optical transceivers can also be an issue for some applications. It's good to remind folks about it, and I know lots of people do use it quite successfully (as have I), but I still prefer to use good 'ol twisted pair, when I can. I always try to buy better cables than I need and those failing latches are the only time I've had an issue with cable quality. Misgar said: I started using second-hand ex-server SFP+ cards in 2018. Examples include the Solarflare 5122F which can be picked up on eBay etc. https://www.serversupply.com/NETWORKING/NETWORK%20ADAPTER/2%20PORT/SOLARFLARE/SFN5122F_222067.htm# My cards are Mellanox. Both mine and yours are PCIe 2.0 x8, which is an issue for a lot of motherboards, where you'd have to drop your graphics card to x8 if you populate the other x16 slot. It should work okay in a slot that's electrically x4, but a lot of boards don't have open-ended slots or slots that are >= x8 and electrically just x4. PCIe 2.0 has a nominal rate of 5 Gbps per lane per direction, but its 8b/10b encoding means you only get 4 Gbps worth of bandwidth. Therefore, you need to run a PCIe 2.0 card at >= x4 to saturate a single 10Gbps link. If you don't mind it being bottlenecked down to only 4 Gbps, I suppose you could put it in a slot that's electrically just x1 (I have a board with some mechanically x16 slots that are just x1 electrically). Some PCIe 3.0 x4 SFP+ cards are becoming more affordable, which is nice to see. But, in the past, the cheap ones always seemed to be those PCIe 2.0 x8 cards, probably because a lot people either can't use them or don't want to make the necessary compromises. Misgar said: Agreed, plus I prefer pure Copper conductors to CCA in RJ45 cables. I accept CCA is cheaper in partition wall installations, but CCA can fail earlier with breaks in frequently used patch leads. Interesting. Most problems I've seen with bad Ethernet cables at work are those with obvious kinks. I'm sure I've seen a couple with no externally-visible damage and attributed those to manufacturing defects. I can't rule out those having failed due to normal handling. Reply
Key considerations
- Investor positioning can change fast
- Volatility remains possible near catalysts
- Macro rates and liquidity can dominate flows
Reference reading
- https://www.tomshardware.com/maker-stem/SPONSORED_LINK_URL
- https://www.tomshardware.com/maker-stem/contractor-builds-ethernet-cable-untwisting-machine-after-facing-100-000-cat6-termination-job-modified-milwaukee-hackzall-straightens-cables-in-under-two-seconds#main
- https://futureplc.com/privacy-policy/
- We tested the RAM-saving storage tech in Gears of War: E-Day
- How NVIDIA Open Source Tools Are Helping Researchers Build Next-Generation 6G Networks
- From Chips to Skills, NVIDIA and Korea Expand Sovereign AI Collaboration
- Jensen Huang could be plotting return as Nvidia CEO, report claims
- Two HPE Juniper network routers grounded all US flights on Friday
Informational only. No financial advice. Do your own research.